जॉर्ज फ्लैट कैप ट्यूटोरियल – छुपा टेप संस्करण छवियाँ पैटर्न डाउनलोड में उपलब्ध हैं. चरण 1 1.5सेमी सीवन भत्ता सभी पैटर्न टुकड़े काटें शामिल. मार्क एक अंक, दर्जी की कील का उपयोग कर बी और सी टॉप पर और पक्ष टुकड़े, चाक या एक ललित की कलम. आप इंटरफ़ेस का उपयोग करना चाहते हो सकता है (लोहा […]
जॉर्ज फ्लैट कैप ट्यूटोरियल छवियाँ पैटर्न डाउनलोड में उपलब्ध हैं. चरण 1 5मिमी सीवन भत्ता सब बाहर कट शामिल पैटर्न टुकड़े. मार्क एक अंक, दर्जी की कील का उपयोग कर बी और सी टॉप पर और पक्ष टुकड़े, चाक या एक ललित की कलम. आप इंटरफ़ेस का उपयोग करना चाहते हो सकता है (या में सीना पर लोहे) […]
छवियाँ पैटर्न डाउनलोड में उपलब्ध हैं. चरण 1 With the two KNOT HAT pieces RIGHT SIDES together, pin around the seam allowance, leaving the lower edge open. पिन ,stitch and trim the seam allowances. चरण 2 कट गया 2 of the BEANIE HAT pattern pieces for the inner hat. With RIGHT SIDES together, fold the […]
छवियाँ पैटर्न डाउनलोड में उपलब्ध हैं. चरण 1 Begin by cutting out the pattern pieces. With RIGHT SIDES together, fold the darts. पिन, stitch and trim the seam allowance of the dart. चरण 2 With the two hat pieces RIGHT SIDES together, pin around the seam allowance, leaving the lower edge open. पिन ,टांका […]
छवियाँ डाउनलोड संस्करण में उपलब्ध हैं. अनुभाग 1 Begin by cutting out the pieces (including lining pieces if you require a lining). Mark the ZIP END on the FRONT of the chaps. If you are using a waterproof fabric, you will want to avoid using pins that will leave a permanent mark on the […]
चरण 1 काटें सभी मुख्य परिधान बैग टुकड़े और अस्तर टुकड़े (अस्तर टुकड़े काट करने के लिए एक ही टुकड़े का उपयोग). वापस टुकड़ा बाहर काटने से शुरू. फिर में वापस पैटर्न टुकड़ा विभाजित 3 नीचे काटने से और डैश रेखाएं भर में. Remember to add 1.5cm seam allowance to the lower […]
चरण 1 सभी टुकड़ों को काटें. चरण 2 Place inner and outer pocket pieces right sides together. पिन और सिलाई. चरण 3 Trim and clip the pocket seam allowance to allow it to lay flat once turned right sides out. चरण 4 Turn pocket right sides out and press flat. चरण 5 Use a large […]
चरण 1 बाहर कट सभी पैटर्न टुकड़े. अंदरूनी केप काटने से शुरू तो धराशायी लाइन के लिए ट्रिम केप ट्रिम कटौती करने के लिए. आप बंद केप ट्रिम अनुभाग का पता लगाने के लिए ताकि आप भविष्य में उपयोग के लिए आंतरिक केप पैटर्न का उपयोग कर सकते हैं चुन सकते हैं. पिन और बाहरी हुड सिलाई 1 के टुकड़े […]
चरण 1 उपयोग ब्रा का पट्टा लोचदार या पूर्वाग्रह कटौती कपड़े है कि केंद्र के लिए दोनों पक्षों मुड़ा कर दिया गया है की लंबाई, तो आधे में फिर से और किनारे के करीब सिले. कट दो लंबाई 50 सेमी लंबी और दो लंबाई 10 सेमी लंबा. तुम भी कुछ ब्रा का पट्टा निष्कर्षों की आवश्यकता होगी (स्लाइडर और छल्ले) के रूप में दिखाया. […]
चरण 1 Begin by cutting out the back guitar piece, followed by the two front pieces (cut from the same pattern piece. Ensure to add the 1.5cm seam allowance to the cutline. Apply a small square of the oil cloth fabric to both ends of the zip. This will be folded back and used to […]